SANSUI APS-310
¥ 103,500 (1 unit, around 1960 s)
Commentary
This is an authentic stereo set that can also be used as furniture.
Receiver section
The amplifier section uses a composite tube 6BM8 push-pull configuration and wide-band output transformer.
The head amplifier uses a combination of a new silicon transistor and a vacuum tube 12AX7 to achieve sound quality with less hum and noise.
A switching matrix circuit is used for the multi-circuit of the FM tuner section.
The output terminal of the center channel amplifier is mounted.
You can enjoy 3D stereo playback by connecting a mono amplifier and a bass speaker to this jack.
It is equipped with a noise filter that removes scratch noise from records, a loudness control circuit, an FM-AFC that stabilizes FM broadcasts, an SCA filter that shuts out interference from SCA broadcasts, and a tape monitor circuit.
It is also equipped with a headphone jack, ferrite antenna for AM and FM stereo indicator.
Player part
It is equipped with a player with an auto mechanism that adopts a newly designed mechanism.
Synchronous phono motor and 30 cm turntable are used for the mechanism part.
Equipped with auto return and auto cut mechanism.
A newly designed static balanced pipe arm with built-in bearing is used for the tone arm.
In addition, a 4-pole, 4-coil MM type cartridge is mounted in the cartridge part.
Speaker part
The speaker section is equipped with a 2-way speaker system.
It has a 25 cm cone woofer in the low range and a 7.5 cm cone tweeter in the high range.
Other
The cabinet has a walnut finish and is designed to allow for separate left and right speakers and center box.
The center box is designed with a vertical amplifier section, and has a structure with a shutter door.
Model Rating
Type | Stereo |
Amplifier Unit | |
Music Power (IHFM) | 22W |
Effective power | 10W/10W 8W + 8W (both channels operating) |
Total harmonic distortion factor | 1.5% (at rated output) |
Power Band Wise (IHFM) | 35 Hz ~ 15 kHz (Distortion Factor 1.5%) |
Frequency characteristic | Aux : 30 Hz to 20 kHz ± 2 dB (1.5%) |
Hum and Noise (IHFM) | Phono : 60 dB (at rated output) Aux : 70 dB at rated output |
Channel separation | Phono:45dB(1kHz) Aux:50dB(1kHz) |
Residual noise | 2 mV or less |
Load impedance | 8 Ω, 16 Ω |
Input sensitivity (1 kHz input required for effective output) | Phono MAG : 3mV/50k Ω Aux : 150mV/360k Ω Tape monitor (pin) : 660mV/100k Ω or more |
Recorded output | 660 mV (for Phono normal input) |
Equalizer | Phono MAG:RIAA |
Tone control | Bass : ± 10 dB (50 Hz) Treble : ± 10 dB (10 kHz) |
Noise filter | -10dB(10kHz) |
Loudness control (vol-30dB) | + 8 dB at 50 Hz, + 8 dB at 10 kHz |
FM Tuner Section | |
Receiving frequency | 76 MHz to 90 MHz |
Sensitivity | 2.5 μ V ± 3 dB (S/N20dB, 30% modulation, 84 MHz) 4 μ V ± 3 dB (S/N30dB, 30% modulation, 84 MHz) |
Frequency characteristic | 30 Hz to 20 kHz ± 3 dB |
Total harmonic distortion factor | 1.5% |
FM Multiplex Section | |
Channel separation | 35dB(1kHz) |
Frequency characteristic | 50 Hz to 15 kHz ± 3 dB |
Total harmonic distortion factor | 1.5% |
<AM Tuner Section> | |
Receiving frequency | 535 kHz to 1605 kHz |
Sensitivity (IHFM) | 30 μ V (1 MHz) |
General amplifier / tuner section | |
Attachment | Tape monitor Headphone Jack (with Switch) Silicon transistor head amplifier Center channel output terminal FM-AFC SCA Filters Magic eye Speaker switch AM ferrite antenna |
Vacuum tubes, transistors and diodes used | Vacuum tube 6AQ8x3 6BA6x3 6BE6x1 6BL8x1 6BN8x2 12AX7x1 6BM8x4 6GE-12A Transistor 2SC402(650)x2 Varicap 1S-351 Germanium diode OA-91x5 Silicon diode SE-05bx2 SE-05-02x1 SH-1(1S-180)x2 |
Pwer | 100 V, 50Hz/60Hz |
Power consumption | 115VA |
<Player Part> | |
Motor | 4-pole synchronous motor |
Turntable | 30 cm Aluminum Die Cast |
Number of revolutions | 33, 45, 78 rpm |
Signal-to-noise ratio | 40 dB or more |
Wow flutter | Not more than 0.25% |
Tone arm | Static balanced non-resonant pipe arm |
Cartridge | MM Type |
Frequency characteristic | 20 Hz to 20 kHz |
Output | 5 mv (5cm/s, 1 khz) |
Channel separation | 20 dB or More (1 kHz) |
Needle pressure | 3g |
Power consumption | 28VA |
Accessory function | Auto return Autocut New type room light |
Speaker Unit | |
Method | 2-Way, 2-Speaker, Sealed Type, Floor Type |
Units Used | For low band : 25 cm cone type For high pass : 7.5 cm cone type |
Max Input | 15W |
Frequency characteristic | 45 Hz to 20 kHz |
Impedance | 16 Ω |
Crossover frequency | 3kHz |
<Others> | |
External dimensions | Width 1,445x Height 654x Depth 390 mm |
Weight | 56.2kg |